You can not select more than 25 topics Topics must start with a letter or number, can include dashes ('-') and can be up to 35 characters long.
mdadm/SOURCES/0064-Update-mdadm-Monitor-m...

120 lines
3.4 KiB

From 725e37cd14866906ba28c970394b9f7a4cd97413 Mon Sep 17 00:00:00 2001
From: Blazej Kucman <blazej.kucman@intel.com>
Date: Mon, 19 Dec 2022 11:21:58 +0100
Subject: [PATCH 64/83] Update mdadm Monitor manual.
- describe monitor work modes,
- clarify the turning off condition,
- describe the mdmonitor.service as a prefered management way.
Signed-off-by: Blazej Kucman <blazej.kucman@intel.com>
Signed-off-by: Jes Sorensen <jes@trained-monkey.org>
---
mdadm.8.in | 71 ++++++++++++++++++++++++++++++++++++++----------------
1 file changed, 50 insertions(+), 21 deletions(-)
diff --git a/mdadm.8.in b/mdadm.8.in
index 70c79d1e..64f71ed1 100644
--- a/mdadm.8.in
+++ b/mdadm.8.in
@@ -2548,13 +2548,33 @@ Usage:
.I options... devices...
.PP
-This usage causes
+Monitor option can work in two modes:
+.IP \(bu 4
+system wide mode, follow all md devices based on
+.B /proc/mdstat,
+.IP \(bu 4
+follow only specified MD devices in command line.
+.PP
+
+.B \-\-scan -
+indicates system wide mode. Option causes the
+.I monitor
+to track all md devices that appear in
+.B /proc/mdstat.
+If it is not set, then at least one
+.B device
+must be specified.
+
+Monitor usage causes
.I mdadm
to periodically poll a number of md arrays and to report on any events
noticed.
-.I mdadm
-will never exit once it decides that there are arrays to be checked,
-so it should normally be run in the background.
+
+In both modes,
+.I monitor
+will work as long as there is an active array with redundancy and it is defined to follow (for
+.B \-\-scan
+every array is followed).
As well as reporting events,
.I mdadm
@@ -2565,15 +2585,6 @@ or
.B domain
and if the destination array has a failed drive but no spares.
-If any devices are listed on the command line,
-.I mdadm
-will only monitor those devices, otherwise, all arrays listed in the
-configuration file will be monitored. Further, if
-.B \-\-scan
-is given, then any other md devices that appear in
-.B /proc/mdstat
-will also be monitored.
-
The result of monitoring the arrays is the generation of events.
These events are passed to a separate program (if specified) and may
be mailed to a given E-mail address.
@@ -2586,16 +2597,34 @@ device if relevant (such as a component device that has failed).
If
.B \-\-scan
-is given, then a program or an E-mail address must be specified on the
-command line or in the config file. If neither are available, then
+is given, then a
+.B program
+or an
+.B e-mail
+address must be specified on the
+command line or in the config file. If neither are available, then
.I mdadm
will not monitor anything.
-Without
-.B \-\-scan,
-.I mdadm
-will continue monitoring as long as something was found to monitor. If
-no program or email is given, then each event is reported to
-.BR stdout .
+For devices given directly in command line, without
+.B program
+or
+.B email
+specified, each event is reported to
+.BR stdout.
+
+Note: For systems where
+.If mdadm monitor
+is configured via systemd,
+.B mdmonitor(mdmonitor.service)
+should be configured. The service is designed to be primary solution for array monitoring,
+it is configured to work in system wide mode.
+It is automatically started and stopped according to current state and types of MD arrays in system.
+The service may require additional configuration, like
+.B e-mail
+or
+.B delay.
+That should be done in
+.B mdadm.conf.
The different events are:
--
2.38.1