jack-audio-connection-kit/jack-audio-connection-kit-README.Fedora

	USING ALSA DIRECTLY

Switch to root account.

Install the required packages:
    yum install alsa-plugins-jack

Add yourself to the jackuser group.
    usermod -a -G jackuser "<your username>"
Now you will need to log out and log back in, or simply restart the system.

Start the jack daemon (the best parameters for your sound card may be different):
    jackd -R -d alsa -d hw:0
This will start jack on the first sound card, at 48KHz sampling rate (can be 
changed with the "-r" command line parameter), with a period of 1024 frames 
(change with "-p", determines the latency) and with 2 interrupts per period 
(change with -n). USB sound cards can benefit from running with "-n 3" or
"-n 4". All of these optional parameters should be specified after "-d alsa".

It is best to replace the card number with the card name as the numbering can
change from boot to boot if there is more than one sound card. The name of a
particular card can be found in the output of "cat /proc/asound/cards", for each
card it is the string between square brackets without the trailing blanks.

Note: Jack is a sound server and not a daemon - while it does work "in the 
background" it is not something similar to unix daemons which are started at
boot time.


	QJACKCTL

This application can be used to control the jack sound server with a graphical
interface. It can be started via
    qjackctl -s
"-s" parameter makes the jack sound server start immediately.

When starting jack through qjackctl it is important to note that you should (at
least) change the "Interface" field in the "Setup" dialog to _not_ be "(default)"
which would point Jack to use Pulse Audio. The proper "Interface" is the direct
hw ALSA device (hw:0 for the first card, etc). Even best to use the name of the
card as stated above.


	INTEGRATE JACK WITH PULSEAUDIO

Jack will ask Pulse Audio through dbus for ownership of the sound card. Pulse
Audio will grant it and Jack will have complete control of it. No conflicts and
no configuration necessary. In this case Pulse Audio will stop using the card
and if it is the only one, you will not have sound for system sounds, browser
media playback, etc (which is usually what you want). Otherwise it is possible
to load a Pulse Audio module that redirects PA to use Jack.


	RUNNING JACK SERVER IN REALTIME MODE

NOTE: This chapter explains why you have done the above changes in more detail.
It is kept for informational purposes. The changes suggested below is done
automatically by your Jack installation and no manual modification of the
pam configuration should be necessary.


The JACK server jackd has the capability to run in a real-time mode
which greatly decreases the chance of audio glitches. The real-time mode
is enabled by passing the -R or --realtime option to jackd when starting
the server. It is only possible to run jackd in real-time mode as a
non-root user by modifying your PAM configuration, PAM stands for
Pluggable Authentication Modules and is the primary authentification
mechanism used on Fedora. The primary source of PAM documentation can be
found at the following at http://www.kernel.org/pub/linux/libs/pam/

The specific PAM configuration file that needs to be modified is
/etc/security/limits.conf and it controls the system resource limits. It
is important to understand that modifying the resource limits
configuration files can decrease the security of your system.
Documentation specific to the resource limits PAM module can be found at
http://www.kernel.org/pub/linux/libs/pam/Linux-PAM-html/pam-6.html#ss6.12

Alternatively, one can create a new file 
   /etc/security/limits.d/<priority>-<name>.conf
that contains the resource limits for individual users and/or groups. The
jack-audio-connection-kit package that comes with Fedora contains the file
   /etc/security/limits.d/99-jack.conf
that does this job for you.

The resource limits that need to be changed to allow jackd to run in
realtime mode are named rtprio and memlock. To increase the limits for a
specific user named fred you would add the following to
/etc/security/limits.conf

fred - rtprio 20
fred - memlock 50000

The value of rtprio can be set in the range 0 - 99 where any value
greater that 0 will allow the user to change the scheduling policy to
"real-time". By default the JACK server requires a minimum rtprio
setting of 20 but jackd will accept a command line parameter -P or
--realtime-priority which will change the minimum required value of
rtprio that is needed, but the default of 20 is nearly always
sufficient.

The appropriate value for memlock is dependent on the amount of memory
present in the system but a minimum value of 50000(50MB) and a maximum
value of half the available memory can be used as a rough guideline. 

To verify that the resource limits have been modified you can use the
bash built-in ulimit command, for example:

$ulimit -a
core file size          (blocks, -c) 0
data seg size           (kbytes, -d) unlimited
max nice                        (-e) 0
file size               (blocks, -f) unlimited
pending signals                 (-i) 8191
max locked memory       (kbytes, -l) 50000
max memory size         (kbytes, -m) unlimited
open files                      (-n) 1024
pipe size            (512 bytes, -p) 8
POSIX message queues     (bytes, -q) 819200
max rt priority                 (-r) 20
stack size              (kbytes, -s) 10240
cpu time               (seconds, -t) unlimited
max user processes              (-u) 8191
virtual memory          (kbytes, -v) unlimited
file locks                      (-x) unlimited
file locks                      (-x) unlimited

Keep in mind that you may have to re-login before changes to limits.conf,
or additions to the limits.d/ directory to take effect.